Difference between revisions of "ThinkPad/A30/SUSE"
(→Thinkpad Configuration: installing packages) |
|||
Line 25: | Line 25: | ||
We were not able to get the thinkpad CLI applet to work. | We were not able to get the thinkpad CLI applet to work. | ||
+ | ===Installing Packages=== | ||
+ | ''(This should eventually be moved to a general [[SUSE]] article, as it doesn't pertain to the Thinkpad in particular.)'' | ||
+ | |||
+ | Having installed a package (in this case, "xpuzzles"), how do you figure out how to run the application(s)? In debian-based distros, [[synaptic]] will at least tell you what files it installed, from which you can figure out what command(s) will invoke it (and whether or not it created any menu entries). But [[yum]] (a Red Hat package manager) and [[YaST]] (the SUSE package manager) seem to lack this feature. (As does Aptitude, though I think the [[CLI]] [[apt (command)|apt]] can still get the info if you know how to use it.) | ||
+ | |||
+ | Or, [[Htwiki:YaST Today|in other words]]... |
Revision as of 02:03, 9 February 2006
Computing: Linux: Thinkpad A30
This article is about running SUSE Linux on an IBM Thinkpad A30.
From The Hypertwins
Overview
We basically had no troubles installing or running the system, aside from two minor incidents:
- The mouse-wheel somehow got deactivated; to reactivate it, we ran (after a bit of hunting) SaX2 (K -> System -> Configuration -> Configure X11 system) which has a mouse configuration page.
- The system began running rather slowly at one point, and KTorrent kept locking up; a reboot displayed error messages accessing sectors on the hard drive, so we ran SpinRite, which found and fixed a bad sector. After that, things were much happier.
We did experience a bit of trouble trying to use the Thinkpad-specific configuration utilities, so here's a bit more on that.
Thinkpad Configuration
We noticed that if we booted up without the (PS/2-connector) mouse plugged in and then connected it after booting up, we could use both the mouse and the eraserhead/keyboard-buttons as mouse controls – whereas if we booted up with the PS/2 mouse plugged in, the eraserhead/keyboad-buttons were disabled. We wanted to see if any of the Thinkpad-specific configuration applets could change this.
There appear to be two places which contain such configuration applets:
- K -> Control Center -> System Administration -> IBM Thinkpad Laptop (which I'll call "thinkpad control module")
- console: configure-thinkpad (which I'll call "thinkpad CLI applet")
On first attempt to run the thinkpad control module, the right panel gave an error message which turned out to be slightly erroneous. Here are the commands which actually work, for enabling the module (run as root):
modprobe nvram mknod /dev/nvram c 10 144 chmod 666 /dev/nvram
("chmod 664" apparently works under most circumstances; only certain models need global-write permission)
After running these commands, click away from the thinkpad control module and then back on it again; it should now work properly.
We were not able to get the thinkpad CLI applet to work.
Installing Packages
(This should eventually be moved to a general SUSE article, as it doesn't pertain to the Thinkpad in particular.)
Having installed a package (in this case, "xpuzzles"), how do you figure out how to run the application(s)? In debian-based distros, synaptic will at least tell you what files it installed, from which you can figure out what command(s) will invoke it (and whether or not it created any menu entries). But yum (a Red Hat package manager) and YaST (the SUSE package manager) seem to lack this feature. (As does Aptitude, though I think the CLI apt can still get the info if you know how to use it.)
Or, in other words...