Woozle's electronic learning kit No. 1 - sample circuits

Electronics: Woozle's electronic learning kit No. 1: parts and such

Introduction

You don't have to make these circuits in the same order they are shown here, but if you are having difficulty getting a circuit to work you might try making sure the one before it works for you.

Actually, you don't have to make any of these circuits at all; the ones shown here are really just to give you an idea of what you can do with just the few components in this kit. Feel free to be creative and try new ideas! But do remember just a couple of things when you are experimenting:

• Don't connect the two battery terminals together without a load between them, because this will drain the batteries very quickly and might make them get very hot (which could damage the holder or the wires), and might make the batteries start to corrode. A switch is not a load, and on the relay only the coil is a load.
• Always disconnect the battery when you are not experimenting. Even if the circuit doesn't seem to be doing anything, it may be draining the battery.

The "Duhhh" Circuit

Ok, you probably know this one, but I'm putting it in here anyway (maybe not everyone knows it):

• connect an alligator clip to one of the battery leads
• pick a lightbulb
• connect the alligator clip at the other end of the wire to one of the leads of the lightbulb
• connect a different alligator clip to the other battery lead
• connect the other end of this alligator clip wire to the other lead of the lightbulb
• Result: the lightbulb should turn on (duhhhh!)

Tips:

• Make sure the metal part of the alligator clip is touching the bare metal part of the wire it is attached to, so electricity can flow from one to the other.

Testing the Relay

Pinout diagram for the relay in this kit. If you look at the underside of the relay – where the wires come out – the pins should be arranged like this. (Ignore the internal arrangement of the coil and NO/NC contacts; it is misleading.)

This is mainly to make sure the relay is working:

• connect an alligator clip to one of the battery leads
• pick a relay
• connect the other end of the alligator clip wire to one of the relay terminals labeled "coil (power)" on the diagram
• connect another alligator clip to the other battery lead
• hold the alligator clip at the other end of that wire and brush it past the other "coil (power)" lead on the relay
• Result: the relay should make quiet "clicking" noises.

Relay Buzzer

Part One

• pick a relay
• connect an alligator clip to one of the "coil" leads on the relay
• connect the alligator clip at the other end to one of the battery leads
• connect another alligator clip to the other "coil" lead on the relay
• connect the alligator clip at the other end of that wire to the "N.C." lead on the relay
• connect one end of a third alligator clip to the other lead from the battery
• connect the other end of this alligator clip wire to the "Common" lead on the relay
• Result: the relay should buzz quietly
• disconnect the clip from the "Common" lead just for now, so we can build the next part of the circuit without that buzzing...

Part Two

• connect the alligator clip you just disconnected (from the "Common" lead) to one of the metal tabs on the back of the switch unit
• find an unused alligator clip wire (this will be the fourth one you'll be using) and clip it on to the metal tab closest to the one connected in the previous step
• connect the other end of this new alligator clip to the "Common" lead of the relay
• Result: if the relay does buzz, then flip the switch and it should start.

Now you can turn your buzzer on and off without disconnecting anything :-)

Part Three

• pick one of the capacitors
• connect an alligator clip to one side of the capacitor (Note: in some circuits it would make a difference which side you connected it to, but in this one it doesn't)
• connect the clip at the other end to the black (negative) lead from the battery
• connect another alligator clip to the other side of the capacitor
• connect the other end of that alligator lead to the "N.C." lead on the relay (you can clip it to the alligator clip already there, if that is easier)
• reconnect the alligator clip from the battery to the relay's "Common" lead
• Result: depending on which capacitor you picked, you will either get a louder buzzing, a harsh rasping noise, or rapid clicking.

You can experiment with disconnecting and reconnecting the capacitor, or trying different capacitors to see what sound they make. (Hint: try the 350µF capacitor, if you haven't already) Or... how about connecting two capacitors at the same time?